How Much Does Drywall Cost in Florida?
Drywall averages $13.20 per sheet in Florida as of 2026 research, with metro-level pricing ranging from $13.20 (lowest-cost metro) to $15.18 (highest-cost metro). That's a 10% premium over the national midpoint of $12.00 per sheet (source; confidence: high). The state midpoint is computed by applying Florida's 1.10× regional adjustment to the national-average dataset documented on our pricing methodology page.
Use the metro table below for finer-grained budgeting — within Florida, the spread between the cheapest and most expensive metro on the same material can run 15-30%.
What Drives Drywall Pricing in Florida?
Florida pricing runs roughly 10% above the national midpoint, driven entirely by hurricane code requirements rather than labor rates (FL labor is below national). Concrete-block construction is the default residential method statewide, post-Andrew code provisions require epoxy-coated rebar within 1 mile of the coast, and the HVHZ overlay in Miami-Dade and Broward stacks another 10-15% on top.
Climate and supply factors: Hurricane-grade wind requirements drive concrete-block construction over wood-frame on most coastal builds — Florida uses 2-3x the per-house concrete of a comparable mid-Atlantic build. Coastal salt-spray exposure requires epoxy-coated rebar within 1 mile of the ocean per FBC corrosion zones.
Drywall Prices by Florida's Major Metros
Per-metro estimates apply each metro's population-weighted price tier to the Florida state midpoint. Population figures are 2024 ACS estimates from the U.S. Census Bureau.
| Metro | Population | Per Sheet | vs. State Avg |
|---|---|---|---|
| Miami | 455K | $15.18 | +15% |
| Tampa | 398K | $13.86 | +5% |
| Orlando | 316K | $13.86 | +5% |
| Jacksonville | 971K | $13.20 | — |
| Fort Lauderdale | 184K | $14.52 | +10% |
When to Buy Drywall in Florida
Construction season in Florida: Year-round; hurricane season (Jun-Nov) compresses pre-storm deliveries and post-storm rebuild demand creates 20-40% spot-price spikes after named-storm landfall.
Drywall pricing is largely seasonal-flat indoors but tightens during peak residential-construction season (May-September) when commercial drywall demand also peaks. For non-emergency work in Florida, ordering during the off-peak window typically saves 5-15% vs. spring/summer peak pricing. Material yards run promotional pricing twice a year — early-spring (Mar-Apr) on bagged products and late-fall (Oct-Nov) on bulk aggregates as plants clear inventory before shutdown.
Climate & Code Considerations for Drywall in Florida
Frost line: 0 in (statewide — no freeze line per IRC R301.2(3)). Frost line drives footing and base depth on hardscape projects — though it has less direct impact on per-sheet drywall pricing.
State / local code: Florida Building Code (FBC) with the High-Velocity Hurricane Zone (HVHZ) overlay covering Miami-Dade and Broward counties — 175+ mph design wind speed, Notice of Acceptance (NOA) product approvals, and impact-rated openings. The Florida Building Code's hurricane provisions and coastal corrosion zones drive concrete-block construction and epoxy-coated rebar in many residential builds — adding cost vs. wood-frame markets.
Where to Find Drywall Suppliers in Florida
Authoritative directories for sourcing ready-mix producers, aggregate quarries, and bagged-product retailers across Florida:
- Florida Concrete & Products Association (FC&PA) member directory
- NRMCA ready-mix producer directory (filter by state)
- Quikrete dealer locator
Get quotes from at least three local suppliers — pricing on the same spec varies 10-20% across producers in the same metro. Volume orders (10+ cu yd ready-mix, 20+ tons aggregate, full pallets bagged) typically earn another 5-10% off published quotes.
Calculate Drywall for Your Project
Use our Drywall Calculator to estimate quantity, then apply Florida's 1.10× adjustment to the national-average cost displayed on the calculator. The calculator's built-in cost overlay uses national pricing — multiply the displayed total by 1.10 for a Florida-specific estimate, or use the per-metro figures in the table above for tighter budgeting.
Frequently Asked Questions
How much does drywall cost per sheet in Florida?
Drywall averages $13.20 per sheet in Florida, with a metro range of $13.20 to $15.18 as of 2026. Florida pricing runs about 10% above the national midpoint.
What is the cheapest Florida metro for drywall?
Jacksonville typically prices the lowest of the major Florida metros, around $13.20 per sheet. Miami typically prices the highest, around $15.18. Differences come from delivery distance to producer plants and metro-area labor rates.
When is the best time of year to buy drywall in Florida?
Year-round; hurricane season (Jun-Nov) compresses pre-storm deliveries and post-storm rebuild demand creates 20-40% spot-price spikes after named-storm landfall. Drywall pricing is largely seasonal-flat indoors but tightens during peak residential-construction season (May-September) when commercial drywall demand also peaks. For non-emergency work, ordering off-peak (late fall in cold-winter states, mid-winter in southern states) typically saves 5-15% vs. spring/summer peak pricing.
What code requirements affect drywall costs in Florida?
Florida Building Code (FBC) with the High-Velocity Hurricane Zone (HVHZ) overlay covering Miami-Dade and Broward counties — 175+ mph design wind speed, Notice of Acceptance (NOA) product approvals, and impact-rated openings. The Florida Building Code's hurricane provisions and coastal corrosion zones drive concrete-block construction and epoxy-coated rebar in many residential builds — adding cost vs. wood-frame markets.
Where can I find drywall suppliers in Florida?
Start with the Florida Concrete & Products Association (FC&PA) member directory, the NRMCA national producer directory filtered to Florida, or the Quikrete dealer locator for bagged products. Get quotes from at least three local suppliers — pricing varies 10-20% across producers in the same metro.
Why is drywall more expensive in Florida than the national average?
Florida pricing runs roughly 10% above the national midpoint, driven entirely by hurricane code requirements rather than labor rates (FL labor is below national). Concrete-block construction is the default residential method statewide, post-Andrew code provisions require epoxy-coated rebar within 1 mile of the coast, and the HVHZ overlay in Miami-Dade and Broward stacks another 10-15% on top.
Related Pages
- All drywall prices by state
- All construction material prices in Florida
- Drywall prices in Texas
- Drywall prices in New Jersey
- Drywall Calculator
- Pricing methodology & sources
Written by Daniel McCarney — AceCalc